 New pictures of wiring.
|
Joined: Jan 2005
Posts: 555
Adjunct
|
OP
Adjunct
Joined: Jan 2005
Posts: 555 |
I uploaded some pics of horn wiring but also repairs of ripped rubber holsters under the gas tank. One of them fell sitting on the engine.
And does anyone know what this open plug is for?
http://www.bonnevilleamerica.com/photopo...=500&page=1
Last edited by ImOk; 08/29/2005 10:30 AM.
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 8,639 Likes: 3
Old Hand
|
|
Old Hand
Joined: Jan 2005
Posts: 8,639 Likes: 3 |
Being a "2 holer" I would guess it's for the aux power plug option. If you can post the colour of the wires without going to a lot of trouble, I'll try to look it up on the wiring diagram tonight.
Let's hope there's intelligent life somewhere in space 'cause it's buggar all down here. -- Monte Python
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 2,297
Oil Expert
|
|
Oil Expert
Joined: Jan 2005
Posts: 2,297 |
I couldn't tell what you used for the replacement? I have one sitting on my engine as I type...
Ryan
In Between the Dark and the Light..
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 2,362
Oil Expert
|
|
Oil Expert
Joined: Jan 2005
Posts: 2,362 |
I've been wondering about that one myself. It's not the aux power connector, as that's got two spade connectors set at right angles to each other. It's the only connector I haven't been able to figure out. Given the small pins and wiring it's unlikely to be a power supply, more likely a controller or display of some type. My thought was that perhaps it was a connecotr for some sort of diagnostic tool for the computer, but I'm probably way off there.
Matt
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 1,204
Learned Hand
|
|
Learned Hand
Joined: Jan 2005
Posts: 1,204 |
It's for the Triumph alarm system
1200CC BIG BORE, W/WISECO PISTONS,.250 STROKED CRANK, PORTED/POLISHED HEADS AND LARGER VALVES, CUSTOM WELDED EXHUAST, DUAL 42MM MIKUNI CARBS.
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 555
Adjunct
|
|
OP
Adjunct
Joined: Jan 2005
Posts: 555 |
I already have the aux plugged in. Makes sense what angelis said about the alarm. Ryan, I did not use a replacement for the rubber holdsters. If you look closely I used plastic wraps around them. Lots of them  .
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 432
Adjunct
|
|
Adjunct
Joined: Jan 2005
Posts: 432 |
looks like you have the 2 horns blocking your oil cooler in the picture.
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 2,362
Oil Expert
|
|
Oil Expert
Joined: Jan 2005
Posts: 2,362 |
Quote:
It's for the Triumph alarm system
You sure you're talking about the little two pin connector, and not the big black twelve (or so) pin connector next to it?
When I wired up my (aftermarket) alarm I only used the twelve pin connector - everything i needed appeared to be there.
Matt
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 1,012
Learned Hand
|
|
Learned Hand
Joined: Jan 2005
Posts: 1,012 |
Hi Sandman,
Just bought myself a Cheetah larm on ebay, i am going to use your instructions when putting it on the bike.
Thanks for sharing the information on your site, i would not have tried on my own without your help!
Gooseman
Bonneville America 904 Black/Silver
Triumph Tiger 1050 Black
Ducati Multistrada 1200s
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 2,362
Oil Expert
|
|
Oil Expert
Joined: Jan 2005
Posts: 2,362 |
Quote:
Hi Sandman,
Just bought myself a Cheetah larm on ebay, i am going to use your instructions when putting it on the bike.
Thanks for sharing the information on your site, i would not have tried on my own without your help!
No problems - glad people are finding it useful. Let me know if you run into any problems.
Matt
|
|
|
Re: New pictures of wiring.
|
Joined: Jan 2005
Posts: 555
Adjunct
|
|
OP
Adjunct
Joined: Jan 2005
Posts: 555 |
Yes, there are two horns. High/low. Sounds like a car. I doubt there is any problem with cooling. Its quite open space and they are small. However it is a good point.
|
|
|
|
|
