 EZ Brackets Question
|
Joined: May 2008
Posts: 11
Complete Newb
|
OP
Complete Newb
Joined: May 2008
Posts: 11 |
I have the ez brackets in use with my Saddlemen Jumbo Drifters. There seems to be a bit of play between the bracket itself and the mounting posts. This causes my bags to shake a bit and seem less than sturdy.
I was wondering if anyone else has this issue or if perhaps there are washers of some sort that come with the brackets that would would tighten them up a bit and eliminate the slight gap there.
Anyone else have this issue? Any ideas?
Thanks in advance.
|
|
|
Re: EZ Brackets Question
|
Joined: Jan 2005
Posts: 11,126 Likes: 13
Should be Riding
|
|
Should be Riding
Joined: Jan 2005
Posts: 11,126 Likes: 13 |
Some play for sure. Now worries. My saddlemans have worn out while attached to the EZ brackets. Loads of miles and loads of stuff. Too much stuff it seems. Think of the mounted bags as how Triumph touts the tiger's hard bags: Floating.
Blowing gravel off rural roads
|
|
|
Re: EZ Brackets Question
|
Joined: Feb 2007
Posts: 23,219 Likes: 61
Fe Butt
|
Fe Butt
Joined: Feb 2007
Posts: 23,219 Likes: 61 |
Wendys never seem to shake, so my question would be how much play and shake you are talking about. Wendys fit pretty tight and are a little difficult getting on and off because they are so snug but I like them that way. If you actually grab them when fully mounted they move just ever so slightly. Not sure about mine they are never on my bike.
I learned all I need to know about life by killing smart people and eating their brains.
Eat right ,Exercise ,Stay fit, Die Anyway!
|
|
|
Re: EZ Brackets Question
|
Joined: May 2007
Posts: 6,432 Likes: 1
Worn Saddle
|
|
Worn Saddle
Joined: May 2007
Posts: 6,432 Likes: 1 |
You can shim the posts with washers to take out the play...just shim one post until the bracket starts to bind a wee bit.
A positive attitude may not solve all your problems, but it will annoy enough people to make it worth the effort. Herm Albright (1876 - 1944)
|
|
|
Re: EZ Brackets Question
|
Joined: Jan 2005
Posts: 8,639 Likes: 3
Old Hand
|
|
Old Hand
Joined: Jan 2005
Posts: 8,639 Likes: 3 |
The holes in the bracket are supposed to be dimpled a little to make them fit snuggly. They are good people and very helpful, so you might want to call their 800 number to see what they suggest.
Let's hope there's intelligent life somewhere in space 'cause it's buggar all down here. -- Monte Python
|
|
|
Re: EZ Brackets Question
|
Joined: Jan 2005
Posts: 5,172
Saddle Sore
|
|
Saddle Sore
Joined: Jan 2005
Posts: 5,172 |
I had my brackets chromed and there's still a bit of play in them.
I've been meaning to try the washer/interference/binding method, but this has been moved way down the "things to worry about" list...
More flags
More fun!
|
|
|
Re: EZ Brackets Question
|
Joined: May 2008
Posts: 11
Complete Newb
|
|
OP
Complete Newb
Joined: May 2008
Posts: 11 |
Thanks guys. I think I'll give the ez brackets folks a call. If nothing else, it shouldn't be too hard to shim them if necessary.
There's no issue cosmetically but my thought was that the constant shaking while riding might cause the (plastic) back of the Saddlemen bags to crack prematurely.
Thanks again.
|
|
|
Re: EZ Brackets Question
|
Joined: Jan 2005
Posts: 11,126 Likes: 13
Should be Riding
|
|
Should be Riding
Joined: Jan 2005
Posts: 11,126 Likes: 13 |
Quote:
... my thought was that the constant shaking while riding might cause the (plastic) back of the Saddlemen bags to crack prematurely.
Thanks again.
The Saddlemen bags will crack prematurely regardless of your concerns if the inboard panels aren't reinforced. Shimming would work to alleviate the wobble at the post, but will have little impact on the inboard wobble. i would venture to speculate and i am unanimous in this, that having tighter brackets would hasten the demise. Back to shimming. Wouldn't take much either. I shimmed one of my post in order to loosen it up a bit. no matter how tight you have the EZ bracket system, the bag will still pull on the EZ bracket attachment points or rather on the whole inboard panel if so reinforced. Shimming to a tight fit the brackets is type A. imho 
Time to go shim mine i guess. 
Blowing gravel off rural roads
|
|
|
Re: EZ Brackets Question
|
Joined: May 2008
Posts: 11
Complete Newb
|
|
OP
Complete Newb
Joined: May 2008
Posts: 11 |
Quote:
....i would venture to speculate and i am unanimous in this, that having tighter brackets would hasten the demise.
I would hope that you are unanimous in your own opinion...
What are you saying? That I'm type A?
Just because everyone I know says that doesn't mean it's true 
|
|
|
Re: EZ Brackets Question
|
Joined: Apr 2007
Posts: 3,063 Likes: 8
Loquacious
|
|
Loquacious
Joined: Apr 2007
Posts: 3,063 Likes: 8 |
Agree with Ian, my EZ brackets are snug. They require a big of wiggling to remove and install. Very little play and no shaking with my Leatherworks bags.
Greybeard is right regarding the dimpling of the brackets. The dimples can and probably will wear/deform with time. Simply redimple to take up the play in the machined grove on the pins(if that can be done??). That should take up the slack rather than trying to use some kind of washer...
12 Rocket Roadster
03 Bonneville America
69 BSA Firebird Scrambler
73 Yamaha TX 750
|
|
|
Re: EZ Brackets Question
|
Joined: Apr 2008
Posts: 280
Adjunct
|
|
Adjunct
Joined: Apr 2008
Posts: 280 |
I've got the exact same combo as you and I've noticed that the bags do seem to rattle a little on the post , but overall I'm very happy with the look and function of the set up.
|
|
|
Re: EZ Brackets Question
|
Joined: Jan 2005
Posts: 11,126 Likes: 13
Should be Riding
|
|
Should be Riding
Joined: Jan 2005
Posts: 11,126 Likes: 13 |
Quote:
I would hope that you are unanimous in your own opinion...
Was alluding to Are You Being Served Dry English Humor.
Blowing gravel off rural roads
|
|
|
|
|
