Check out the new Gallery
wicked red 1100
wicked red 1100
by mag10, August 21
Windshield I need to replace
Windshield I need to replace
by philwarner, May 10
first ride
first ride
by NemoJr, April 1
Steve McQueen inspired
Steve McQueen inspired
by Feral, November 28
GaRally22
GaRally22
by chy, September 18
Previous Thread
Next Thread
Print Thread
Valve clearance ?
#144391 03/26/2007 4:24 PM
Joined: Jan 2005
Posts: 592
Adjunct
OP Offline
Adjunct
Joined: Jan 2005
Posts: 592
I have just got around to checking my valves (20000 + miles)today. Exhaust side .28,.29,.25,.28 Intake side .21,.23,.23,.21 Ok all you valve guru's should I have them adjusted or not. Thanks.

Re: Valve clearance ?
alabama_al #144392 03/26/2007 4:38 PM
Joined: Jan 2005
Posts: 4,074
Likes: 83
chy Offline
Loquacious
Offline
Loquacious
Joined: Jan 2005
Posts: 4,074
Likes: 83
Check out FJ's write up about it in the Tech Vault lots of good info including specs and procedures.

Re: Valve clearance ?
alabama_al #144393 03/26/2007 7:15 PM
Joined: Jan 2005
Posts: 1,335
tcv Offline
Learned Hand
Offline
Learned Hand
Joined: Jan 2005
Posts: 1,335
The following is the spec for our bikes

Valve clearance Intake .15 - .20 mm
Valve clearance Exhaust .25 - .30 mm

Based on this I would say you need to adjust all your Intake valve shims.

Tom


Those who would give up essential liberty to purchase a little temporary safety deserve neither liberty nor safety. Benjamin Franklin, US author, diplomat, inventor, physicist, politician, & printer (1706 - 1790)
Re: Valve clearance ?
alabama_al #144394 03/26/2007 7:48 PM
Joined: Jan 2005
Posts: 9,223
Big Bore
Offline
Big Bore
Joined: Jan 2005
Posts: 9,223
You are out on the intakes and close to the top on 3 of 4 on the exhaust. I'd re-shim them. Use Pat's shim calculator (the Lounge Link Stash has a direct link) and a good micrometer and you can probably cross swap some of your shims to bring them into the center of tolerance. Definitely adjust.


"Never underestimate the power of human stupidity" - Robert Heinlein
Re: Valve clearance ?
alabama_al #144395 03/27/2007 12:18 AM
Joined: Jan 2005
Posts: 18,825
"Lighten up, Francis."
Offline
"Lighten up, Francis."
Joined: Jan 2005
Posts: 18,825
Those are pretty loose. Mine were all too tight.


BA.com Caretaker | Friarsride | jb.com
Re: Valve clearance ?
bonnyusa #144396 03/28/2007 3:29 PM
Joined: Jan 2005
Posts: 1,335
tcv Offline
Learned Hand
Offline
Learned Hand
Joined: Jan 2005
Posts: 1,335
Phil,

When I adjusted mine I did them all to the high side. The way these engines are designed the gap will never get larger, but over time as the valves wear it will get smaller. If I am wrong please let me know.

Tom


Those who would give up essential liberty to purchase a little temporary safety deserve neither liberty nor safety. Benjamin Franklin, US author, diplomat, inventor, physicist, politician, & printer (1706 - 1790)

Moderated by  bennybmn, chy, mert 

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.4