Portal Forums Calendar Active Threads
Check out the new Gallery
wicked red 1100
wicked red 1100
by mag10, August 21
Windshield I need to replace
Windshield I need to replace
by philwarner, May 10
first ride
first ride
by NemoJr, April 1
Steve McQueen inspired
Steve McQueen inspired
by Feral, November 28
GaRally22
GaRally22
by chy, September 18
Previous Thread
Next Thread
Print Thread
Tech drawings
#137383 03/03/2007 12:32 AM
Joined: Nov 2006
Posts: 5
Calen Offline OP
Complete Newb
OP Offline
Calen
Complete Newb
Joined: Nov 2006
Posts: 5
Forgive me if this has been posted elsewhere, but I couldnt find it. Does anyone know a link for the tech drawings of the engine for a 06 TBA? My roommate is a machinist and swears he can make anything for my engine my heart desires. All I need is the tech specs and drawings for him to go off of. I can't seem to find them though. Any help would be greatly appreciated.
Re: Tech drawings
Calen #137384 03/03/2007 1:31 AM
Joined: Jan 2006
Posts: 7,685
Likes: 20
San Antonio
satxron Offline
Monkey Butt
Offline
satxron
Monkey Butt
Joined: Jan 2006
Posts: 7,685
Likes: 20
San Antonio
I wish he could make two aluminum pulleys for a belt drive.

Have not seen a full set of drawings for the motor, sorry.

I try to aggravate one person a day. Today may be your day.
Re: Tech drawings
Calen #137385 03/03/2007 2:40 PM
Joined: Jan 2005
Posts: 62
Buckeye, Az
DanB Offline
Member
Offline
DanB
Member
Joined: Jan 2005
Posts: 62
Buckeye, Az
See if he can make the oil pump drive gears to get rid of the plastic ones. Just need to find a set to copy.

1970 Bonneville, 2001 Yamaha 250 Virago (Wife's), 2003 Speedmaster
Re: Tech drawings
DanB #137386 03/03/2007 8:35 PM
Joined: Feb 2006
Posts: 3,099
USA-CT-NORWALK
unclecharlie Offline
Loquacious
Offline
unclecharlie
Loquacious
Joined: Feb 2006
Posts: 3,099
USA-CT-NORWALK
Check with angelis, I think he's doing this.
Re: Tech drawings
DanB #137387 03/03/2007 10:50 PM
Joined: Aug 2006
Posts: 153
Hanover PA
SCCTrim Offline
Adjunct
Offline
SCCTrim
Adjunct
Joined: Aug 2006
Posts: 153
Hanover PA
Quote:

See if he can make the oil pump drive gears to get rid of the plastic ones. Just need to find a set to copy.



Theres a company in Maryland that is already making them in bronze I believe. Pretty sure they are out of Timonium

http://www.sccinc.us.com
Re: Tech drawings
SCCTrim #137388 03/04/2007 12:10 AM
Joined: Sep 2006
Posts: 1,457
Capital of The Sunshine State
Lonzo Offline
Learned Hand
Offline
Lonzo
Learned Hand
Joined: Sep 2006
Posts: 1,457
Capital of The Sunshine State
Roundslide had them made out of bronze, I can't find the thread on it.
Re: Tech drawings
Lonzo #137389 03/05/2007 1:01 AM
Joined: Jan 2005
Posts: 1,204
BROKEN ARROW
ANGELIS745 Offline
Learned Hand
Offline
ANGELIS745
Learned Hand
Joined: Jan 2005
Posts: 1,204
BROKEN ARROW
Guys I was going to make them in bronze but the cost would be prohibited. I have some made up already but are being tested by Pat(Dinqua) and someone else. Again I want to be sure the tolerences and material are correct....Also being worked on are the CDI units.....It takes time to do the job right(plus the expense of developing a CDI unit is coming out of my pocket)....Angelis

1200CC BIG BORE, W/WISECO PISTONS,.250 STROKED CRANK, PORTED/POLISHED HEADS AND LARGER VALVES, CUSTOM WELDED EXHUAST, DUAL 42MM MIKUNI CARBS.

Moderated by  chy, Dinqua, freedom 

Link Copied to Clipboard
Rides
Forum Rules · Mark All Read Contact Us · Forum Help · Bonnevilleamerica.com
Powered by UBB.threads™ PHP Forum Software 7.7.4